Documents / Report

The Roswell Report: Fact vs. Fiction in the New Mexico Desert

USAF / The Black Vault · 1995 · 882 pages · text by OCR

The Roswell Report: Fact versus Fiction in the New Mexico Desert was published by Headquarters United States Air Force in 1995. The Black Vault distributes this copy. It reproduces the report by Col. Richard L. Weaver and the synopsis by 1st Lt. James McAndrew, both written after a General Accounting Office inquiry requested by Representative Steven Schiff. The Air Force search found no evidence of an extraterrestrial craft or crew. It concluded that the Roswell debris most likely came from NYU Flight No. 4, a Project MOGUL balloon train.

  • p. 118 …Robert Gross and Mr. Maher of Lockheed 11:55 A.M. Gen. Sam Anderson 12:00…
  • p. 393 …in the form of an altitude vs. gross load chart with helium as the lifting gas…
  • p. 394 …4}{\text {Gross Load}} = \frac {K}{W} $$ In turn, $ \frac{K}{W}=a e^{-0. 4…
  • p. 395 …free lift in pounds and G is gross lift in pounds. Although this equation was derived…
  • p. 400 …By equation (10), with a gross load of 52 kg., the unbalance caused by loss of…
  • p. 412 …or a gross buoyancy of 450 lb., the maximum allowable inflation of a 30' diameter, .001…
  • p. 479 …accelerating force equal to 5% of the gross load (52 kg) was acting to bring the…
  • p. 552 …000 feet. In one step, this becomes: Gross Lift/Balloon = (Balloon Volume) x (Difference in molecular…
  • p. 555 …of rise in feet per minute G = gross lift in grams For our purposes, we wish…
  • p. 559 …G) ^ {\frac {2}{3}} $$ (Approximate) where G = gross load A chart, Figure 24, has beendrawn up…
  • p. 561 …where $ \triangle G= $ loss of lift G = gross load (balloon weight plus equipment load) $ \triangle T…
  • p. 562 …not including balloon or its integral parts. Gross load: Load on the gas at release (Balloon…
  • p. 635 …Serial No. ___ description ___ ___ Line length ___ Banner description ___ ___ Ballast assembly - description ___ ___ Eallast. ___ Total Equipment Weight. ___ Gross Load ___
  • p. 636 …Gross Load . . . ___ Assumed Gross Lift (Gross Load + 10%) G ___ G 2/3 ___ Free Lift - F = $ (\frac…
  • p. 649 …theoretical altitude determined by the displacement and gross load. ## 7. Control systems Two systems of control…
  • p. 681 …By adjusting the gross load to be supported by the gas to equal the total lift…
  • p. 691 …A chart showing the relation between altitude, gross lift, and balloon size has been found necessary…
  • p. 775 …The gross load reported should be accurate to the nearest 200 grams. The amount of lifting…
  • p. 777 500 gm DRAG CHUTES 300 " BANNER 2000 " PAYLOAD 4500 " BALLOON 7300 " GROSS LOAD ## NOTE: Use low…
  • p. 779 …bubble length and resultant inflated volume, using gross lift as an expression of volume. It will…
  • p. 781 …in Appendix II summarizes the relationship between gross load and floating level for balloons of several…
  • p. 817 …A can of sand is made to weigh the same amount as the required gross lift…
  • p. 825 …the balloon with the equipment load attached. Gross Lift: Lift of all of the gas in…
  • p. 830 …Serial No. ___ description ___ Drag chute ___ ___ Banner description ___ ___ Ballast assembly - description ___ ___ Ballast ___ Total Equipment Weight . ___ Gross Load . . . . . . . . . . . . . . . . ___
  • p. 831 …waiting___ grams Actual balloon lift . . . . . . . . . . . ___ " AActual gross lift (Balloon lift & balloon wt.) . . . . . ___ " Number Helium tanks required…
  • p. 835 …Gross Lift vs. Bubble Length . . . . . . . 107 Graph 3: Buoyancy vs. Altitude . . . . . . . . . . 108 Graph 4: Gross Load…
  • p. 847 …Estimated Gross Load Limit kg. Altitude Range ft. 7 200 0.6 1.5 to 5…
The physical and chemical properties needed in a balloon material are: (1) chemical stability, (2) low permeability, (3) high tensile strength, (4) low brittle temperature, (5) high tear resistance, (6) high transparency to heat radiation and (7) light weight.

In Table 1 the properties of 7 plastics and 2 coated materials are given. From this data polyethylene and saran appear to be the most suitable films.

Table 1

Fabric	Low Temperature Properties	Permeability	Tensile Strength	Tear Resistance	Ease of Fabrication	Stability to Ultraviolet
Polyethylene	Good	Medium	Low	Good	Good	Good
Saran	Fair	Low	High	Poor	Fair	Fair
Nylon	Good	Low	High	Low	Good	Good
Vinylite	Very poor	Medium	Medium	Good	Good	Good
Teflon	Believed good	Low	High	Good	Cannot be fabricated	Good
Ethocellulose	Good	Very high	Low	Fair	Good	Good
Pliofilm	Poor	High	Poor	Fair	Good	Poor
Nylon or silk fabric coated with:Neoprene	Fair	Low	High	Fair	Fair	Fair
Butyl rubber	Good	Low	High	Fair	Fair	Good

Having decided upon the proper fabric to be used, an effort was made to interest a number of companies in the fabrication and production of balloons. The first supplier of balloons made of polyethylene was Harold A. Smith, Inc., Mamaroneck, New York. In these balloons, 4 and 8 mil sheets were heat sealed to form a spherical cell open at the bottom. Load attachment tabs were set into the fabric and loading lines ran from these tabs to a load ring. This method of supporting the load proved to be unsatisfactory.

Cited by

Cases discussed

About this file

Report, cited by the archive. The PDF is mirrored here; the original link is under it. The text was read from the page images by an OCR model; expect the odd misread word. 882 pages are in the text index: search them above, or from the library's search.