Documents / FOIA release

roswell

Office of the Secretary of Defense · 993 pages · text from the file's own layer

The Roswell Report: Fact versus Fiction in the New Mexico Desert was published in 1995 by Headquarters United States Air Force. It was written in response to Representative Steven H. Schiff's request and a General Accounting Office audit, and it contains Col. Richard L. Weaver's report and 1st Lt. James McAndrew's synopsis, along with attachments, appendices and photographs. The report says researchers found no evidence of an extraterrestrial craft or crew. It concludes that the 1947 debris came from a Project MOGUL balloon train.

  • p. 143 …Robert Gross ar.d 't!r. Jlaher of Lockheed 11~ 55 A.'.!. Gen. Sam Anderson 12…
  • p. 481 …Balloon Volume x Gas Lift Gross Load · It may be noted from this equation that a…
  • p. 482 …Balloon Volume x 24.4 Gross Load K =-w K _ 08.o475Z In turn, w-in…
  • p. 483 …free lift in pounds and G is gross lift in pounds. Although this equation was derived…
  • p. 488 …By equation {10), with a gross load of 52 kg., the unbalance caused by loss of…
  • p. 500 …or a gross buoyancy of 450 lb. • the maximum allowable infle.tion of a 30' diameter…
  • p. 569 …accelerating force equal to 5% of the gross load (52 kg) was acting to bring the…
  • p. 643 …000 feet. In one step, this becomes: Gross Lift/Balloon = (Balloon Volume) x (Difference in molecular…
  • p. 650 (Approximate) where G • gross load A chart, Figure 24, has beendrawn up, based on this equation…
  • p. 652 …G = loss of lift G =gross load (balloon weight plus equipment load) AT : mean temperature difference…
  • p. 653 …not including balloon or its integral parts. Gross load: Load on the gas at release (Balloon…
  • p. 726 …Ballast • • .. • • '" • Total Equipment l~eight. • • • • ' Gross Load • • ' • • • • {56)
  • p. 727 …Balloon volwne x gas litt/mol gross load cu. ft. -----------------NAximum Altitude • • • ft, m.s.l…
  • p. 741 …altitude deter- mined by the displacement and gross load. 7. Control systems Two systems of control…
  • p. 777 …By adjusting th~ gross load to be supported by the gas to equal the total lift…
  • p. 787 …Computations A chart showi~ the relation between altitude, gross lift, and balloon size has been found…
  • p. 883 …The gross load reported should be accurate to the nearest 200 grams. The amount of lifting…
  • p. 885 …A L L 0 0 N 7300 ,, GRoss LoAD Fl G. 17 NYU BALLOON pROJECT I…
  • p. 887 …bubble length and resultant inflated volume, using gross lift as an expression of volume. It will…
  • p. 889 …in Appendix II summarizes the relationship between gross load and floating level for balloons of several…
  • p. 925 …A can of sand is made to weigh the same amount as the required gross lift…
  • p. 933 …the balloon with the equipment load attached. Gross Lift: Lift of all of the gas in…
  • p. 938 …description.______________ Drag chute ---------------------------- Banner description --------------- ---------- Ballast assembly - description -----------~-- Ballast • • • • • • Total Equipment i'ieight • • ' • • • • • • Gross Load • • • • • • • • • • • -86-
  • p. 939 …wnitin_,g________ grams Actual balloon lift • • • • • • • • ". . .• II AActunl gross lift (Balloon lift & balloon wt.) • Number Helium…
  • p. 943 …Gross Lift vs. Bubble Length • • • • • • .107 Graph 3: Buoyancy vs. Altitude • • • • • • • • • .108 Graph 4: Gross Load…
  • p. 955 …BALLOOO DA 'fA General Mills Actual Balloon Estimated Gross Altitude ~ominal Diiameter Volwne Weight Load Limit…
1020 millibars) against. percentage of the turns
as read on the nomogram. The lowest pressure
reading is numbered as read and succeeding
pressures are plotted in a continuous ascending
series. When the pressure reading reached the
first_overlap on the reference, it is called
100 percent; the second overlap is 200 percent
and so on until the last overlap which may be
1200 or 1300 percent.
(c) Pack the modulator and insert it inside the
transmitter box. The modulator should be pro-
tected from extreme cold since the motor opera-
tion becomes erratic when the temperature reached
:soo to 400C below zero. A box or paper cover
over the modulator will keep particles of in-
sulation and dirt from the moving parts.
(d) When the entire assembly has been made and in-
flation of the balloon is about to begin, the
transmitter and motor should be turned on and
reception of the signal tested. If any serious
trouble appears, the modulator should be re-
placed by another calibrated modulator since
any work on the instrument will probably change
the calibration.
During the flight,radio static and noise will
appear on the Brush record as pips which may re-
semble the transmitted signals and with increasing
distance or weakening transmitter the noise will
finally completely obscure the pressure record.
Careful tuning of the receiver will prolong
the record as long as possible. When tuning
the receiver, the sensitivity control of the
Brush amplifier should be turned to the least sen-
sitive position since any sudden change in the
tuning may throw the pen off its supports and
damage its glass tip.
'When the flight reception is completed the re-
cord is evaluated exactly as in the evaluation
of the calibration record--using the same nomo-
gram. However, since the instrument is subjected
to different atmospheric condition~, the motor
speed may vary suddenly, giving false values for
the pressure. These values may be detected by
carefully observing the rate of rotation of the
motor, which is measurable by the distance be-
tween the reference marks. If there is a sudden
-61-

Cases discussed

About this file

FOIA release, from the osd collection. The PDF is mirrored here; the original link is under it. 993 pages are in the text index: search them above, or from the library's search.