Documents / FOIA release
roswell
Office of the Secretary of Defense · 993 pages · text from the file's own layer
The Roswell Report: Fact versus Fiction in the New Mexico Desert was published in 1995 by Headquarters United States Air Force. It was written in response to Representative Steven H. Schiff's request and a General Accounting Office audit, and it contains Col. Richard L. Weaver's report and 1st Lt. James McAndrew's synopsis, along with attachments, appendices and photographs. The report says researchers found no evidence of an extraterrestrial craft or crew. It concludes that the 1947 debris came from a Project MOGUL balloon train.
“Gross”26 pages
- p. 143 …Robert Gross ar.d 't!r. Jlaher of Lockheed
11~ 55 A.'.!. Gen. Sam Anderson
12…
- p. 481 …Balloon Volume x Gas Lift
Gross Load ·
It may be noted from this equation that a…
- p. 482 …Balloon Volume x 24.4
Gross Load
K
=-w
K _ 08.o475Z
In turn, w-in…
- p. 483 …free lift in pounds
and G is gross lift in pounds.
Although this equation was derived…
- p. 488 …By equation
{10), with a gross load of 52 kg., the unbalance caused by loss
of…
- p. 500 …or a gross
buoyancy of 450 lb. • the maximum allowable infle.tion of a 30'
diameter…
- p. 569 …accelerating
force equal to 5% of the gross load (52 kg) was acting to bring the…
- p. 643 …000 feet.
In one step, this becomes:
Gross Lift/Balloon = (Balloon Volume) x (Difference in molecular…
- p. 650 (Approximate)
where G • gross load
A chart, Figure 24, has beendrawn up, based on this equation…
- p. 652 …G = loss of lift
G =gross load (balloon weight plus
equipment load)
AT : mean temperature difference…
- p. 653 …not including balloon or its integral
parts.
Gross load: Load on the gas at release (Balloon…
- p. 726 …Ballast • • .. • • '" •
Total Equipment l~eight. • • • • '
Gross Load • • ' • • • •
{56)
- p. 727 …Balloon volwne x gas litt/mol
gross load
cu. ft.
-----------------NAximum Altitude • • • ft, m.s.l…
- p. 741 …altitude deter-
mined by the displacement and gross load.
7. Control systems
Two systems of control…
- p. 777 …By adjusting th~ gross load to be
supported by the gas to equal the total lift…
- p. 787 …Computations
A chart showi~ the relation between altitude, gross lift, and
balloon size has been found…
- p. 883 …The gross load reported should be
accurate to the nearest 200 grams. The amount of lifting…
- p. 885 …A L L 0 0 N
7300 ,, GRoss LoAD
Fl G. 17
NYU BALLOON pROJECT I…
- p. 887 …bubble length and resultant inflated volume,
using gross lift as an expression of volume. It will…
- p. 889 …in Appendix II summarizes the relationship between gross
load and floating level for balloons of several…
- p. 925 …A can of sand
is made to weigh the same amount as the required gross lift…
- p. 933 …the balloon with the equipment
load attached.
Gross Lift: Lift of all of the gas in…
- p. 938 …description.______________
Drag chute ----------------------------
Banner description --------------- ----------
Ballast assembly - description -----------~--
Ballast • • • • • •
Total Equipment i'ieight • • ' • • • • • •
Gross Load • • • • • • • • • • •
-86-
- p. 939 …wnitin_,g________ grams
Actual balloon lift • • • • • • • • ". . .•
II
AActunl gross lift (Balloon lift & balloon wt.) •
Number Helium…
- p. 943 …Gross Lift vs. Bubble Length • • • • • • .107
Graph 3: Buoyancy vs. Altitude • • • • • • • • • .108
Graph 4: Gross Load…
- p. 955 …BALLOOO DA 'fA
General Mills Actual Balloon Estimated Gross Altitude
~ominal Diiameter Volwne Weight Load Limit…
pending upon the speed or rotation of the mo-
dulator motor. The pressure signal appears
at any point along the record between or over-
lapping the references depending upon the pressure.
A sample record of this sort is shown in Figure 32.
The Olland cycle acts as a ~itching unit for the
test oscillator (see Figure 33) whose agnal· is fed
into the Brush amplifier and finally to the recorder.
By adjusting the resistors in the test circuit,
the frequency ot oscillation may be adjusted. Since
within the usual range, the frequency of oscillation
is approximately additive when the two signals over-
lap. the suggested frequencies are about 4 cycles per
second for pressure and 8 cycles per second for refer·
ence. When overlapping signals are being recorded
the frequency will be about 12 cycles per second
which is easily recognizable on the record.
The calibration of the modulator unit should be
in steps of 25 to 30 millibars in order to have
at least three points within each turn of the
helix.
Evaluation of the record is accomplished with
the aid of a nomogram divided into 100 equal
parts. The record is laid on the nomogram with
the leading edge of the first reference on the
zero line and the leading edge of the second
reference on the lOOth line. The position of
the leading edge of the pressure signal is then
read to the nearest third of a division on the
nomogram. If one complete turn of the spiral
represents 75 millibars, it is thus possible
to read the pressure to an accuracy of one-
three-hundreth of 75 or about one-quarter milli-
bar.
In evaluating the record the tape should be kept
parallel to the horizontal lines on the nomogram
or perpendicular to the zero line in order to
avoid errors in ir..terpretation.
The total motion of the pen arm of the modulator
is normally 12 to 14 turns of the spiral. Therefore,
there will be the same number of points at which
the pressure and reference signals overlap. The
calibration curve (Figure 34) is drawn to show
pressure from zero to surface pressure (about
-57-
About this file
FOIA release, from the osd collection. The PDF is mirrored here; the original link is under it. 993 pages are in the text index: search them above, or from the library's search.