Documents / Official release
This file from the Agency Liaison records in the Clinton Presidential Records contains a 1997 report by Steven M. Greer of CSETI on its Washington briefings of April 7 to 11, 1997. The report describes a closed briefing that nearly 30 congressional offices attended, a briefing at the Pentagon and a background briefing for the media. It calls for open congressional hearings with 107 identified government witnesses. The file also includes Mark McCandlish's 1989 cutaway drawing of an "Alien Reproduction Vehicle."
Read from the scan by GLM-OCR; expect the odd misread word.
I. THE OUTER PANELS OF THE "SKIRT" OF THE FUSELAGE ARE MADE OF A COMPOSITE MATERIAL LAMINATE SUCH AS FIBERGLASS, KEVLAR OR CARBON FIBER. THE SIDES SLOPE AT APPROXIMATELY 35° FROM THE VERTICAL. EACH IS ATTACHED BY DZUS FASTENERS, WITH A SLIGHT OVERLAP ALONG THE VERTICAL SEAMS. J. THE "ANTENNA SECTION" IS HELD IN PLACE BETWEEN THE FLANGES ON THE UPPER AND LOWER HALVES OF THE CREW COMPARTMENT SPHERE, AND APPEARS TO BE THE SECONDARY WINDINGS OF A LARGE TESLA COIL, WITH AN INNER DIAMETER OF ABOUT TWELVE FEET. IT IS EIGHTEEN INCHES WIDE ON THE TOP SURFACE AND IS NINE INCHES IN TOTAL THICKNESS. INSIDE THIS SECTION ARE COPPER-COLORED "BANDS OR CABLES" ABOUT ONE QUARTER OF AN INCH THICK, SEPARATED BY THREE-EIGHTHS OF AN INCH IN A GREEN, TRANSLUCENT, DIELECTRIC MATERIAL, POSSIBLY "G-10" GLASS. THE OUTER EDGE OF THIS SECTION IS "MILLED" AT ABOUT A 35° ANGLE FROM THE VERTICAL. NOTE THE SIMILARITIES TO TESLA U.S. PATENT NO. 593,138, ISSUED 2 NOVEMBER, 1897. K. THIS ARTICULATED, ROBOTIC ARM IS CAPABLE OF EXTENDING OUTWARD THROUGH TWO HINGED PANELS ON THE "SKIRT" OF THE A.R.V. WITH A "REACH" OF ABOUT TEN TO FIFTEEN FEET. A FLANGED PEDESTAL IS BONDED TO THE UPPER SURFACE OF THE "CAPACITOR SECTION". L. THE "CAPACITOR SECTION" IS ABOUT TWENTY-FOUR FEET IN DIAMETER, TWELVE TO FOURTEEN INCHES THICK, AND DIVIDED INTO FORTY-EIGHT NARROW, WEDGE-SHAPED SECTIONS, APPROXIMATELY 7.5° IN ARC-WIDTH, WITH EIGHT COPPER-COLORED PLATES, ONE-HALF OF AN INCH THICK, STACKED UP IN EACH SECTION. THE PLATES AND EACH CAPACITOR SECTION ARE SEPARATED BY THREE-QUARTERS OF AN INCH OF A GREEN, TRANSLUCENT, DIELECTRIC MATERIAL, POSSIBLY "G-10" GLASS OR A SIMILAR MATERIAL. NONE OF THE PLATES ARE EXPOSED TO THE AIR. THE OUTER RIM OF THE CAPACITOR SECTION APPEARED TO HAVE BEEN MILLED OFF AT A 35° ANGLE FROM THE VERTICLE, AS IF BY A HUGE LATHE. M. INDIVIDUAL CAPACITOR PLATES ARE MADE OF BILLIONS OF COMPRESSED, 15 MICRON COPPER SPHERES TO DRAMATICALLY INCREASE THE SURFACE AREA FOR CONDUCTING OF ELECTRICAL CURRENT. FLIGHT OF THIS CRAFT IS ACHIEVED THROUGH A COMBINATION OF CASIMIR FORCE AND THE "BIEFIELD-BROWN EFFECT". (SEE U.S. PATENT NO. 3,187,206, ISSUED JUNE 1, 1965; TWO YEARS BEFORE THE WENDELL STEVENS PHOTO WAS TAKEN). DIRECTIONAL CHANGES ARE EXECUTED BY VARYING THE AMOUNT OF CURRENT DELIVERED TO INDIVIDUAL CAPACITOR SECTIONS, PRODUCING THE EFFECT OF YAW AND PITCH. CURRENT IS DISTRIBUTED AT AN EXTREMELY HIGH FREQUENCY, POSSIBLY AS HIGH AS 30 TO 150KHz (THOUSANDS OF CYCLES PER SECOND). CHARGE DISTRIBUTION IS DIVIDED INTO TWO, COUNTER-ROTATING "CHANNELS" EACH HAVING 24 SECTIONS, AND USING EVERY OTHER SECTION, WITH THE OPPOSING CHANNEL USING THOSE IN BETWEEN. ADJACENT SECTIONS HAVE INDIVIDUAL PLATES STACKED IN LATERALLY OPPOSED ORDER, WHERE THE PLATES OF ONE SECTION ALLIGN WITH THE GAPS BETWEEN THE PLATES IN THE SECTIONS ON EITHER SIDE OF IT. N. THE SA N. APPROXIMATELY 24 OXYGEN/AIR TANKS ARE MOUNTED AROUND THE CIRCUMFERENCE OF THE CRAFT, STRAPPED INTO TWO SADDLES CONSTRUCTED OF A COMPOSITE MATERIAL THAT IS BONDED TO THE UPPER SURFACE OF THE "CAPACITOR SECTION". THESE TANKS ARE OF A "PULTRUDED" CONSTRUCTION, USING COMPOSITE MATERIALS AND ARE TWELVE TO FOURTEEN INCHES IN DIAMETER, AND ABOUT SIX FEET IN LENGTH.
Official release, from the nara collection. The PDF is mirrored here; the original link is above. The text was read from the page images by GLM-OCR; expect the odd misread word. 21 pages are in the text index: search them above, or from the library's search.